What is Wrong With My Twitter FL Settings?

[Chicilikit]

Hello, I run about 100 accounts, but few days ago it seems like they all stopped to follow anyone or follow extremely low numbers. Unfollowing probably still works, because now I see almost all my account does not follow anyone. I use shared proxies from actproxy, they say no more than 3 poeple per shared proxy, but Im not sure if its the proxy where the problem is or it is anything else. I have only profile picture and bio on my accounts, they should be PVA, and usually no more than 1-2 tweets on those accounts. They are about 14 days old. I tried to run 10-15 now 50 threads, does not seem to change anything. Thanks for any help guys, im getting desperate.

 

[Chicilikit]

forgot to add this

 

[Chicilikit]

So nobody knows?

 

[brodel34]

What did FL support tell you?

 

[Floopa75]

OP on both Follow User Settings and Unfollow Settings, your daily limit is set properly. But then right above it "follow limit" and "unfollow limit" are both way too low. Those to numbers need to be the same as daily follow/unfollow on both pages.

So on your follow user page put follow limit to 500-1000
Unfollow page put unfollow limit to 50-360.

Side note, if your accounts are only 14 days old you are pushing them way too hard. When people say you can push hard on "aged" accounts they mean accounts that are 6+ months, or accounts with a lot of followers. You will more than likely be suspended with these settings right now, my advice is to downscale.

 

[lennyserrano]

I never used this software before so I am not sure, but from what I can tell from the first picture, you have "unfollow" and "follow" checked, so that mean your accounts are trying to do both tasks at the same time and twitter doesn't like when you follow to unfollow the same day, I assume that is why you're not getting the results you wanted maybe.

 

[Floopa75]

I never used this software before so I am not sure, but from what I can tell from the first picture, you have "unfollow" and "follow" checked, so that mean your accounts are trying to do both tasks at the same time and twitter doesn't like when you follow to unfollow the same day, I assume that is why you're not getting the results you wanted maybe.

Followliker will only do one checked task at a time meaning it will do a sequence of following for however long, then wait 4-6mins, then it might go into unfollowing to check if there;s any possible unfollowing that it can do, if not it will bounce out of that wait another 4-6mins and go back into following people

 

[wizard04]

OP I had the same problem.

How to fix it:

Go to File > Clear > All Scraped Users

This will fix your problem. FL has a Bug if it have to much Scraped users it will stop following.
I clear my scraped users when the number of scraped users get near 200K

 

[Chicilikit]

Thansk a lot for all help guys. I will try it.

 

[Jamboree]

I'm having the same problem, so if anyone figures it out, let me know.

 

[Chicilikit]

I have found solution for my problem, I used wrong query format with "https://twitter.com/account", when I changed to just "account" it started working. But overall this software is nightmare for users, things like this I did not see in manual, error messages are almost none, you cannot simply backup so I lost like ten hours of work once, you cannot bulk add queries. And when I contact support it takes them at least whole day to answer simple question, but their answer is always few words and nothing what really solves your problem. Anyone who will create more user friendly bot will make nice money if developers of this will not keep working on these issues.

 

[MarkInDK]

While I partly agree that FL can be a bit cumbersome to work with, I disagree that it's a nightmare.

It's fairly straightforward software, and doing a bit of testing usually leads to understanding of the software.

Now, to think of it as simply plug & play is perhaps too much... Personally I found I gained great amounts of knowledge by simply testing it out, with quite conservative settings to start.

 

[PUT0M0N0]

Im having the same issue. Any suggestion? What about change the general settings? Thanks in advance!